Top 10 Arduino Ethernet Shield – Single Board Computers

As an Amazon Associate I earn from qualifying purchases.

1. SunFounder

#ad

SunFounder Ethernet Shield W5100 for Arduino R3 Mega 2560 1280 A057

#ad
SunFounder #ad - With this ethernet Shield, for Arduino board can be used to connect to internet. Can be used as server or client. It adds a micro-sd card slot, which can be used to store files for serving over the network. Directly plug puzzle board, no soldering required. It is directly compatible with Arduino official Ethernet Library.
BrandSunFounder #ad
ManufacturerSunFounder #ad
Height1.5 Inches
Length7 Inches
Width5.8 Inches
Part NumberFBA_DE W5100
ModelFBA_DE W5100

2. Arduino

#ad

Ethernet Development Tools ARDUINO ETHERNET SHIELD 2

#ad
Arduino #ad - Requires an Arduino Board not included. Ethernet controller: W5500 with internal 32K buffer. Operating voltage 5V supplied from the Arduino Board. Connection speed: 10/100Mb. Connection with Arduino on SPI port.
BrandArduino #ad
ManufacturerArduino #ad
Height2 Inches
Length4 Inches
Weight0.04 Pounds
Width3 Inches
Part NumberA000024
ModelA000024

3. XCSOURCE

#ad

XCSOURCE ATmega2560-16AU ATMEGA16U2 Board + Ethernet Shield W5100 Network Expansion TE168

#ad
XCSOURCE #ad - It has 54 digital input/output pins of which 14 can be used as pwm outputs, 4 UARTs hardware serial ports, a power jack, a 16 MHz crystal oscillator, a USB connection, an ICSP header, 16 analog inputs, and a reset button.

The mega is compatible with most shields designed for the Arduino Duemilanove or Diecimila. The board is a microcontroller board based on the ATmega2560-16AU. The mega 2560 is an update for the Arduino Mega, which it replaces. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started.
BrandXCSOURCE #ad
ManufacturerXCSOURCE #ad
Height1.5 Inches
Length10 Inches
Width7.8 Inches
Part NumberTE168
ModelTE168

4. seeed studio

#ad

Seeed studio W5500 Ethernet Shield

#ad
seeed studio #ad - Supports wake on lan over udp. Supports 8 independent sockets simultaneously. Internal 32kbytes memory for tx/rx buffers. The rj45 port where the ethernet cable is connected to is low enough to allow you to stack more shields on top of this one if needed.

Led outputs full/half duplex, udp, arp, speed, icmp, active.10baset/100basetx ethernet phy embedded. Supports power down mode. Supports hardwired tcp/ip protocols : tcp, igmp, ipv4, link, pppoe. Supports high speed serial peripheral interfacespi mode 0, 3. Supports auto negotiation full and half duplex, 10 and 100* based. The shield also have two grove connectors and a microsd card socket to support projects which require storing large amounts of data from grove sensor.
Brandseeed studio #ad
ManufacturerSeeedstudio #ad
Part Number8.41454E+11
Model8.41454E+11

5. HiLetgo

#ad

HiLetgo ENC28J60 ENC28J60-I/SO HR911105A Ethernet LAN Network Module SPI Interface 3.3V for Arduino AVR PIC LPC STM32

#ad
HiLetgo #ad - Main chip:dip28 enc28j60-I/SO. Rj45 connector hr911105A isolation transformer. Compatible with 51, lpC, avr, STM32 MCU.3. 3v power supply with spi interface support connecting with 8/16/32 bit MCU. The board 25MHZ crystal.
BrandHiLetgo #ad
ManufacturerHiLetgo #ad
Part Number3-01-0185
Model3-01-0185

6. RobotDyn

#ad

Mega 2560 Ethernet W5500 + Micro SD Card Reader/Writer with PoE, Mega ETH with PoE, Compatible for Arduino. Arduino Mega Ethernet Shield w5500 Active PoE., RobotDyn

#ad
RobotDyn #ad - Select arduino mega 2560 in the «Boards» menu, and use Ethernet3 / Ethernet4 library. Esp-01 wi-fi on board have socket for connecting Wi-Fi ESP-01 module. The micro sd card can be used to save and store the data, which can later be transferred over the network. Build a network connected device: your arduino mega 2560 board can be used to connect to internet with this RobotDyn Ethernet Shield w5500 Wi-fi module connecting to Serial3interfaceviaRX3D15/TX3.

Micro sd card reader/writer with poe: the ethernet shield w5500 board also features a Micro SD card socket. The board is equipped with an rj45, 12 of which can be used for PWM, DC power jack, micro USB, and a reset button. The ethernet controller and microSD card are connected through the SPI bus. The best premium alternative for arduino ethernet shield mega and ethernet controller W5500 and with Wi-Fi module ESP-01! Arduino mega 2560 r3 form-factor: programming in arduino ide: robotdyn mega 2560 eth r3 can be programmed via an Arduino IDE.

W5500 is using a highly efficient spi protocol, W5500 provides WOL Wake on LAN and Power Off modes. It comes with LAN and Wi-Fi connection. It provides tcp/ip stack, 10baset/100basetx ethernet with full or half-duplex, with 80 mhz clocks for high-speed connectivity to Atmega2560 For lower energy consumption, MAC and PHY.
BrandRobotDyn #ad
ManufacturerZhuhai RobotDyn Technology Co.,Ltd (China) #ad
Height0.79 Inches
Length4.72 Inches
Weight0.14 Pounds
Width2.36 Inches
Part Number6970622936916

7. KEYESTUDIO

#ad

Easily Connects Arduino to Internet, KEYESTUDIO W5100 Ethernet Shield for Arduino Mega 2560 Controller R3 Duemilanove

#ad
KEYESTUDIO #ad - It can turn your arduino into a simple web server or use the Internet to read /write its digital and analog outputs/inputs. Keyestudio w5100 ethernet Shield gives you an easy way to get your Arduino Online. How to use: search for "keyestudio wiki KS0156" in Google Chrome to get the wiki online tutorial for this product. Adds a micro-sd card slot, can be used to store files for serving over the network. It also supports the read &write of mini SD card TF card. It is directly supported by arduino official Ethernet Library.
BrandKEYESTUDIO #ad
Manufacturerkeyes #ad
Height1.3 Inches
Length4.4 Inches
Weight0.1 Pounds
Width2.7 Inches
Part NumberKS0156
Model8541582678

8. HiLetgo

#ad

HiLetgo W5100 Ethernet Network Shield W5100 Ethernet Expansion Board with SD Card Slot for Arduino UNO MEGA2560

#ad
HiLetgo #ad - Direct plug puzzle board, NO soldering needed. With micro sd card slot, supports 2009, uno, mega 2560, mega 1280, Nano, supports sd card up to 2GB, Duemilanove. The ethernet w5100 network expansion module allows the Arduino to be a simple Web server. Supports reading and writing mini SD / TF card. Ethernet shield with wiznet W5100 ethernet chip.
BrandHiLetgo #ad
ManufacturerHiLetgo #ad
Height2.9 Inches
Length4.5 Inches
Weight0.26 Pounds
Width3.6 Inches
Part Number3-01-0441-D
Model8541585431

9. FTCBlock

#ad

FTCBlock Ethernet Shield W5100 for Arduino UNO R3 Mega 2560 1280 A057

#ad
FTCBlock #ad - Can be used as server or client. Directly plug puzzle board, no soldering required. With this ethernet Shield, your Arduino board can be used to connect to internet. It adds a micro-sd card slot, which can be used to store files for serving over the network. It is directly supported by Arduino official Ethernet Library.
BrandFTCBlock #ad
ManufacturerSouthern Tech #ad
Part Numberftw51

10. RobotDyn

#ad

W5500 Nano V3 Ethernet Network Shield, Module for use with Arduino Nano, RobotDyn

#ad
RobotDyn #ad - Use the Ethernet3. H library to write sketches which connect to the internet. Based on the tcp/ip wiznet w5500 ethernet chip. Supports wol - wake on LAN. 8 independent sockets. Internal 32KB memory for serial buffers. Led outputs full/half duplex, speed, link, active.10baset/100basetx ethernet phy embedded. Supports power down mode.
BrandRobotDyn #ad
ManufacturerZhuhai RobotDyn Technology Co.,Ltd #ad
Height0.79 Inches
Length2.36 Inches
Weight0.04 Pounds
Width1.18 Inches
Part Number6970622936831